铝电解电容器
ALUMINUM ELECTROLYTIC CAPACITORS
东莞市军田电子有限公司
DONGGUAN JUNTIAN ELECTRONICS CO.,LTD
1．产品名称(Products Name)：
ST-LH 系列铝电解电容器
ST-LH series aluminum electrolytic capacitors
2．产品外形及安装(Products Configuration and Installation)：
圆柱形、金属外壳、单向引出、引出方式为螺栓式,有极性、有压力释放
装置(采用点动防燃装置，当电容器内压增加或产品发生击穿时不会有易燃品飞
出)。采用卡环固定安装，不适用于直接安装在线路板上。
Cylindrical form, metal case, unidirectional leads, derivative fashion is screw,
polarity, press release device (It is from a point. When the capacitor’s internal
pressure was increased or product was breaked ,inflammable materials will not fly
down)。Adoption card wreath fix install, not well used for direct install
Circuit plank top
3.适用范围及特征(The Scope and Characteristics)：
该产品主要应用于点焊机、充磁机、工业变频器、UPS 电源、高压真空断路器、
交流接触器、高压柜、低压柜、激光点焊机、激光美容机、开关电源、通信电源等电子设备，具有使用温度范围宽、可靠性高、能承受大纹波电流等特点。（ The products are mainly used in Disply, Inverter, UPS Electrical Source and other Switching power supply circuits of electronic equipments. They have high reliability, withstand
the large ripple current and other characteristics.Case can be adjusted appropriate under the
request of the customer.）
4．性能要求(Performance Requirements)：
项目Item 特征Characteristics
环境温度
Operating Temperature Rang (℃)
-25℃~85℃(160~600wv,-20℃~85℃)
容量变化率
Capacitance Tolerance (20℃\120Hz)
±20%
漏电流
Leakage Current (μA)
0.01CV or 5mA,whichever is smaller. 取小值（at 20
℃,after 5 minutes 5 分钟后）C:Nominal Capacitance
(μF),V:Rated Voltage(V)
损失角正切值
Dissipation Factor(20℃ 、120Hz)
小于规格表值
Less than the value specified in the standed
Products tables
寿命试验
Load Life (+85℃)
时间Time 10000h
漏电流
Leakage current
小于规定值Not more than
the specidied value
容量变化率
Capacitance change
初始值的±10%以内
Within±20%of the initial
value
损失角正切值
Dissipation Factor
不大于2 倍规定值
Not more than 200% of
specified value
贮存试验
Shelf Life (+85℃)
时间Time 10000h
漏电流
Leakage current
小于规定值Not more than
the specidied value
容量变化率
Capacitance change
初始值的±10%以内
Within±10%of the initial
value
损失角正切值
Dissipation Factor
不大于2 倍规定值
Not more than2% of specified
value
After test:uR to be applied for 30 minutes,24 to 48 hours
before measurement
试验后：施加额定电压30 分钟，放置24~48 小时后测试
铝电解电容器
ALUMINUM ELECTROLYTIC CAPACITORS
东莞市军田电子有限公司
DONGGUAN JUNTIAN ELECTRONICS CO.,LTD
长期有效供应35v150000uf大功率大容量电容
1．产品名称(Products Name)：
ST-LH 系列铝电解电容器
ST-LH series aluminum electrolytic capacitors
2．产品外形及安装(Products Configuration and Installation)：
圆柱形、金属外壳、单向引出、引出方式为螺栓式,有极性、有压力释放
装置(采用点动防燃装置，当电容器内压增加或产品发生击穿时不会有易燃品飞
出)。采用卡环固定安装，不适用于直接安装在线路板上。
Cylindrical form, metal case, unidirectional leads, derivative fashion is screw,
polarity, press release device (It is from a point. When the capacitor’s internal
pressure was increased or product was breaked ,inflammable materials will not fly
down)。Adoption card wreath fix install, not well used for direct install
Circuit plank top
3.适用范围及特征(The Scope and Characteristics)：
该产品主要应用于点焊机、充磁机、工业变频器、UPS 电源、高压真空断路器、
交流接触器、高压柜、低压柜、激光点焊机、激光美容机、开关电源、通信电源等电子设备，具有使用温度范围宽、可靠性高、能承受大纹波电流等特点。（ The products are mainly used in Disply, Inverter, UPS Electrical Source and other Switching power supply circuits of electronic equipments. They have high reliability, withstand
the large ripple current and other characteristics.Case can be adjusted appropriate under the
request of the customer.）
4．性能要求(Performance Requirements)：
项目Item 特征Characteristics
环境温度
Operating Temperature Rang (℃)
-25℃~85℃(160~600wv,-20℃~85℃)
容量变化率
Capacitance Tolerance (20℃\120Hz)
±20%
漏电流
Leakage Current (μA)
0.01CV or 5mA,whichever is smaller. 取小值（at 20
℃,after 5 minutes 5 分钟后）C:Nominal Capacitance
(μF),V:Rated Voltage(V)
损失角正切值
Dissipation Factor(20℃ 、120Hz)
小于规格表值
Less than the value specified in the standed
Products tables
寿命试验
Load Life (+85℃)
时间Time 10000h
漏电流
Leakage current
小于规定值Not more than
the specidied value
容量变化率
Capacitance change
初始值的±10%以内
Within±20%of the initial
value
损失角正切值
Dissipation Factor
不大于2 倍规定值
Not more than 200% of
specified value
贮存试验
Shelf Life (+85℃)
时间Time 10000h
漏电流
Leakage current
小于规定值Not more than
the specidied value
容量变化率
Capacitance change
初始值的±10%以内
Within±10%of the initial
value
损失角正切值
Dissipation Factor
不大于2 倍规定值
Not more than2% of specified
value
After test:uR to be applied for 30 minutes,24 to 48 hours
before measurement
试验后：施加额定电压30 分钟，放置24~48 小时后测试